Soundcraft Spirit Folio 12 2 User Manual

Advertising
Soundcraft Spirit Folio 12 2 User Manual

INITIAL SETTING UP

You will probably use your SPIRIT FOLIO RAC PAC with a wide range of different types of sound source, and these will

be at varying signal levels. It is important to set the GAIN of the inputs correctly to give the best performance.

Set up the individual Mono input channels as follows:

The power supply contains no user-serviceable parts. Refer all servicing to a qualified service engineer, through the appropriate Soundcraft dealer. INTRODUCTION SAFETY PRECAUTIONS 1 In memory of Kousuke Matsui ‚ A Man of Spirit ‚.

Soundcraft Spirit Folio 12 2 User Manual

••

  1. May 18, 2012  1 user review on Soundcraft Spirit Folio 12/2. A good old analogue desk, antique, no frills here, you connect its cables, adjusting the knobs and tweaked it by ear.
  2. View online Quick overview for SoundCraft SPIRIT FOLIO Music Mixer or simply click Download button to examine the SoundCraft SPIRIT FOLIO guidelines offline on your desktop or laptop computer. SoundCraft MPM 12/2 User Manual Operation & user’s manual (32 pages) SOUNDCRAFT NOTEPAD 102 User Manual Operation & user’s manual.

Plug in the chosen source (usually the MIC input for mics and the LINE input for anything else). Plug in phantom

powered mics before switching the phantom power on. Set the channel fader fully down.

••

Set the Group and Master Faders at ’0’ and GROUPS TO MIX pressed.

••

Select MIX to C/Room & Phones.

••

Check that SOLO MODE is released.

Soundcraft Spirit Folio 12 2 User Manual

••

Release the channel routing switches to route to Groups 1-2

••

Provide the chosen source with a typical signal level and press the latching PFL button by the fader. The level of

signal will be shown on the right-hand Bargraph Meter (the Left meter will be switched off when the PFL button is

down).

••

Adjust the input GAIN until the meter is just reaching the amber LED (0dB) at a typical maximum source level with

a steady signal. If the source signal is rich in high-level transients (e.g. drums) a rather higher meter reading of

+6/+9 will be needed to achieve an equivalent average level. This leaves enough headroom to cope with peaks

in the signal without distortion.

••

Adjust each input channel in the same way.

••

If you find that you cannot set a reasonable level within the range of the GAIN control when using a MIC input

on the Mono channels, try the LINE input instead.

Stereo inputs 11-14 do not have a GAIN control, since the typical source for these inputs will be external tape machines

or effects units which have a much more predictable signal level. Set the +4/-10 switch to +4 (released) initially, and

check the input level with the PFL switch as decribed above. If the level is too low, switch to the -10 input setting.

You will now have initial settings for each of the input sources and are ready to start building a mix.

••

Connect your power amplifiers and speakers and set the gain of the amplifiers to about 70%.

••

Move the individual channel faders gradually to the required working level, listening carefully for any hint of

feedback or overload. You may find that the input gain settings will need to be edged back slightly as the mix is

built up.

••

Listen carefully for the characteristic sound of ‘feedback’. If you cannot achieve a satisfactory input level setting

without feedback, adjust microphone and speaker positions and try again.

Careful microphone placement and the choice of a suitable type of microphone is important for vocals. The aim should

be to place the microphone as close as possible to the source, to cut out unwanted surrounding sounds. This allows a

lower gain setting on the mixer and helps to avoid feedback. You will also find that a well-placed microphone will not

need any appreciable equalisation.

SPIRIT FOLIO RAC PAC

5

Advertising
Popular Brands

Soundcraft Spirit Folio Power Supply

Popular manuals